VM-2240 System Management Amplifier (ER Version)

VM-2240 System Management Amplifier (ER Version)

VM-2240 System Management Amplifier (ER Version)

VM-2240 ER

The VM-2240 is a multifunctional amplifier that can be mounted in an EIA-Standard equipment rack (3-unit size). The unit comes with 4 audio inputs including the background music input, and the speaker output section which has an internal attenuator and 5-zone selector. It permits not only general-purpose broadcast, but also Emergency Broadcast based on the EN60849 Standard which gives pre-recorded voice instructions(*1) in the emergency situation. Broadcast can be made from an optional RM-200M Remote Microphone as well as from the amplifier, and can be remotely controlled from external equipment. In addition, for 100 V/42 Ω application the unit features the surveillance function(*2) which automatically checks the system for failures. (*1) An optional EV-200M Voice Announcement Board is required. (*2) An optional SV-200MA Surveillance Board is required.

(*3) 0 dB= 1 V
Power SourceAC: 230 V
DC: 24 V/15 A
Applicable cable diameter: AWG22 - AWG14
Power Consumption on AC MainsWith no signal present: 54 W
Under normal operating conditions according to
EN60065: 1998 sec. 4.2: 255 W
With rated output signal: 549 W
Current Consumption on 24 V DC Power InputWith no signal present: 1 A
Under normal operating conditions according to
EN60065: 1998 sec. 4.2: 5 A
With rated output signal: 14 A
Rated Output240 W
Output Voltage /Impedance100 V/42 Ω
(selectable by the internal wiring change)
Frequency Response50 Hz - 16 kHz
Distortion1 % or less
Signal-to-Noise Ratio60 dB or more
Tone ControlBass: 100 Hz ±10 dB
(Inputs 1 - 3 and BGM individually adjustable.)
Remote Microphone /Expansion Amplifier Connection2 RJ45 female connectors for connecting the RM-200M Remote
Microphone and the VM-2120 or VM-2240 unit used as an
expansion amplifier.
Maximum distance: 800 m (874.89 yd) in total
Link cable: Category 5 Shielded
Number of connectable RM-200M's: Up to 4
Twisted-Pair straight cable (TIA/EIA-568A standard)
InputInputs 1 - 3: -60 dB(*3) (MIC)/-10 dB(*3) (LINE) (changeable)
600 Ω
combined XLR connector (female)/phone jack
(Only Input 1 is additionally equipped with DIN
connector(*5).)
Telephone paging input: Push-in terminal block(*6)
Voice sound: -10 dB(*3)
balanced input with shield terminal(*4)
Control: No-voltage make contact input
open voltage: 3.3 V DC
short-circuit current: under 1 mA
BGM 1 - 2: -20 dB(*3)
Power amplifier input: 0 dB(*3)
External speaker line input: 100 V line
(This input is selected when the "Unit's
broadcast cutoff" control is activated.)
OutputSpeaker output: Plug-in screw connector(*7)
5-zone selector with attenuator (all zones simultaneously
selectable)
Direct speaker line output: Direct output from the power amplifier
output transformer (attenuator bypassed)
Plug-in screw connector(*7)
Line output: 0 dB(*3)
Recording output: 0 dB(*3)
Preamplifier output: 0 dB(*3)
Control InputFor controlling Inputs 1 - 3
No-voltage make contact input
short-circuit current: 1 mA or less
Control Input and OutputD-sub connector (25-pin
Input: No-voltage make contact input
short-circuit current: 1 mA or less
Output: Open collector output
control current: 10 mA or less
(1) External control input
Activation of messages(*8)
Activation of power
Activation and stop of Emergency Broadcast
Unit's broadcast cutoff
(when activated by an external emergency equipment)
(2) Status output
Irregularity of communications with the Remote Microphone and
an expansion amplifier
AC power condition
DC power condition
Irregularity of the sound source of the Voice Announcement Board
Failure (FAULT) indication on
Power switch on
External Attenuator Control OutputPlug-in screw connector(*7)
transfer type
contact current: 7 A (DC) or less
Surveillance Input and Output(*9)D-sub connector (25-pin
Input: No-voltage make contact input
Output: Open collector output
Power Supply24 V DC/0.1 A
Unit RU-2001/-2002
Chime ToneBuilt-in chime: 2-tone chime/2-tone chime (fast repeat)/4-tone
chime (Up)/Single-tone chime/4-tone chime (Up &
Down)/Gong/off
Voice Announcement Board sound source: Pre-recorded chime(*8)
FunctionTwo units stacking (VM-2120 or VM-2240)
Emergency broadcast (sequential control)
Broadcast priority control
Surveillance (failure detection) function(*9)
Power supply to only one Remote Microphone (RM-200M)
Line resistance: 40 Ω (one way) or less
Operating Temperature0 ℃ to +40 ℃ (32 %%dF to 104 %%dF)
FinishPanel: ABS resin
Case: Steel plate
Dimensions419 (W) × 143.3 (H) × 355.7 (D) mm (16.5 × 5.64" × 14)
Weight14.5 kg (31.97 lb)
AccessoryPower cable (2 m (6.56 ft)) ……1
Miniature type time-lag fuse T3.15 A ……1
OptionRack mounting bracket: MB-36
Input transformer: IT-450
Voice announcement board: EV-200M
Surveillance board: SV-200MA


Scroll to top